真人做人爱试看一

    <strike id="cvpmt"></strike>

      Your position:Home > Products > Sludge Drying

      Hot Air Stirring Fluid Dryer

      Final moisture: lower than 5% 
      Output: capacity : 0.5-20t/h 
      Applications: it is widely applied to dry sludge, gypsum, ore slurry, bentonite, brewer grain, pomace, medicine dreg, bean dregs, candy pomace, soy sauce residue, peat and rare earth. 

      Sales Hotline:

      0086-18539990967

      Technical introduction

        By adopting double-shaft mixing and screw propulsion, Our TDOCD-D hot air mixing dryer is a kind of drying equipment which can finish ideal drying effect rapidly. It is especially suitable to dry viscous and high-moisture materials. It can dry materials with 65% moisture content to final 5% to 15% moisture one time. Its drying period is short, generally 2 to 50 minutes. Owing to fierce mixing of high-speed mixing blades, we materials can contact fully with hot air under floating state. In the front part of dryer, evaporation speed of raw material is faster and the temperature of hot air in dryer drops down sharply. Therefore, even though using high-temperature hot air, temperature increase of raw materials is not very high.
        Hot air mixing dryer is always used to dry typical high-moisture materials, such as: 

      coal slime, sludge, gypsum, ore slurry, bentonite, vinasse, pomace, medicine dregs, bean dregs, sugar residue, soya residue, peat and rare earth; 
      organic materials, sludge compound materials and chemical raw materials, powder particle and flake high-moisture raw material. 

      Advantages

      Great drying strength
      Owing to high velocity of air flow, materials can be evenly distributed in hot air mixing dryer. Almost each part of materials can be regarded as effective drying area. Meanwhile, owing to dispersion and agitation function, gasification surface can be updated continuously. Therefore, heat transfer process is very strong.

      Short drying time
      There will be a concurrent flow between materials and airflow. Temperature of both materials and air can reach to a reasonable state. Drying time is very short, so pretty high drying temperature can be adopted.

      Wide application
      Wide application, high output capacity, great moisture reduction, simple structure, small area occupation, less investment and maintenance cost.
      Multiple heat source option, less energy consumption
      Oil furnace, gas furnace, coal furnace, steam heat exchanger; less energy consumption and less running cost.

      Reasonable design
      Compact design; less area occupation, less noise, less vibration, PLC control system, safe and reliable; matched with efficient furnace and tail gas purification system, the whole system is characterized by high efficiency, low energy consumption and no pollution. 

      Working principle

       Hot air dryer adopts double-shaft mixing and screw propulsion to dry sticky and high-moisture materials. Hot air dryer can dry materials with 65% moisture to below 5% to 12% at one time. Drying period is very short, 2 to 20 minutes. Blades in hot air dryer can stir wet materials intensively, wet materials can contact fully with hot air. Moisture content of wet materials can be greatly evaporated faster in the former half part. Temperature of hot air in dryer drops sharply. Therefore, although hot air dryer applies hot air with high temperature, the temperature of raw materials will not increase greatly. 


      hot air double shaft stirring drying system

      Technical parameters

      Item  Unit Model
         TDOSC-D1500   TDOSC-D2500    TDOSC-D3500      TDOSC-D5500 
      Moisture Reduced  kgH20/hr 1500 2500 3500  5500
      Maximum Flow of Wet Material  kg/h  10000  15000  25000       40000 
      Maximum Moisture of Wet Material % 90 90 90 90
      Output Moisture  % 12-50 12-50 12-50 12-50
      Installed Capacity  Rotor Shaft Motor  kw 22x2 22x2 30x2 45x2 
      Scraper Shaft Motor  kw 5.5 5.5 5.5 5.5
      Back mixing motor  kw 2.2 2.2  2.5  2.2 
      Temperature of Inlet Hot Air 350-800 350-800 350-800 350-800
          Overall Dimension mm  4500x2100
      x4000
      5700x2100
      x4500
      6700x2100
      x4500
      7700x2100
      x4500
          Equipment Weight  kg 10500 12000 18000 25000

      Relevant cases

      Order Online

      Please pay attention: in order to get timely contact with you, please leave us your complete information such as your contact number, your demand (types of your raw materials, volume, feed size and size of final products); you can also contact us by business link. Really hope we can be your stasified partner.

      • Product:
      • Name:
      • Email:
      • Usage Region:
      • Your Demand:

      Sludge Reclamation

      Matching Device

      Sales hotline:0086-18539990967

      Address of headquarters:NO. 198, longding industrial zone, high-tech development zone, zhengzhou city, china

      Email:vip@tdaxy.com

      Zhengzhou Taida Group    Address:NO. 198,longding industrial zone,high-tech development zone,zhengzhou city,china    Sitemap

      真人做人爱试看一

        <strike id="cvpmt"></strike>